AUS PROPERTY REPORT logo

Access Limitations for your inspector

Understand the access limitations inspectors face during pre-purchase building inspections. Know what occurs during a pre-purchase building inspection.

Why Access Matters in a Building Inspection

When you book a pre-purchase building inspection, it’s easy to assume the inspector will check everything. But the reality is, they’re working within the guidelines of the Australian Standard AS 4349.1 - Pre-purchase inspections of residential buildings. This includes clear limits on what can and can’t be accessed.

Building inspections are visual and non-invasive. That means inspectors won’t move furniture, climb unsafe roofs, or enter locked areas. If a part of the property is unsafe, inaccessible, or obstructed, it may be excluded from the report altogether.

Understanding these access limitations helps you:

  • Avoid assuming the entire property has been fully inspected
  • Ask the right questions when reviewing your report
  • Decide if further, more specialised inspections are needed

Before you rely on your report to make a big decision — make sure you know what the inspector was actually able to see.


What AS 4349.1 Says About Access Limitations

Pre-purchase building inspections in Australia must follow the AS 4349.1–2007 standard and one of the most important (but often misunderstood) parts of the standard is access.

Inspectors can only assess accessible areas, which are defined as:

“Areas of the site where sufficient, safe and reasonable access is available to allow inspection within the scope of the inspection.”

If something blocks access, it’s considered a limitation, which the standard defines as:

“Any factor that prevents full or proper inspection of the building.”

What Is “Reasonable Access”?

According to the standard an inspector is only required to inspect areas that are safely and reasonably accessible without the use of specialised tools or destructive methods.

The standard outlines the following minimum access requirements for certain areas:

  • Roof Void (Roof Space):

    • Access opening at least 400mm x 500mm
    • 600mm minimum crawl space
    • Accessible from a safe platform or ladder
  • Roof Exterior:

    • Accessible from a ladder no more than 3.6m in height
    • Must be safely reachable without climbing on fragile roofing
  • General Areas:

    • Must be unobstructed (no heavy storage, locked doors, unsafe structures)

Subfloor areas are not assigned a specific height or clearance requirement.

Instead, the extent of what is considered accessible is determined by the inspector.

The standard notes:

“The extent of the accessible area shall be determined by the inspector at the time of inspection, dependent on the conditions encountered at the time of inspection. The inspector shall also determine whether sufficient space is available to allow safe access.”

This means if the area is too tight, obstructed, or unsafe, the inspector may determine it as restricted or inaccessible in the final report.


Common Access Limitations

Here are some of the most common reasons an inspector may not be able to access parts of the property:

  • Locked rooms or areas - If the inspector cannot gain entry due to a locked door or gate, they cannot inspect that space.
  • Low or restricted subfloor clearance - The standard does not specify a fixed height requirement. Instead, the inspector determines whether there is sufficient and safe clearance to enter. If it’s too low or obstructed, access may be restricted or not possible.
  • Roof voids with inadequate access - Access points or crawl spaces that are too small or obstructed can prevent a safe inspection. Falling through a ceiling is no fun.
  • Unsafe roof exterior - If the roof is wet, slippery, fragile, or otherwise unsafe, the inspector may not access it.
  • Furniture or stored goods - Inspectors are not expected to move furniture or stored goods to access walls, floors, or ceilings behind or beneath them.
  • Insulation or coverings - Inspectors are not to disturb insulation, lift floor coverings, or remove wall linings or unscrew access panels.
  • General concealments – Ducting, wall cavities, bulkheads, suspended plumbing.

When access is limited or not possible, the inspector should clearly state this in the report, including the reasons why access was restricted, and may recommend further inspection once access becomes available.


Tips to Maximise Access Before Inspection

To get the most comprehensive report, consider the following:

  • Request keys are available for all rooms and outbuildings, if possible
  • Request clear access to manholes, subfloor access panel (unscrewed if applicable)
  • You can request a car to be removed, outside of that, best to respect peoples space and time

Why This Matters for Buyers

Uninspected areas = Unknown risks.

A clean report doesn’t always mean a clean property—especially if critical spaces weren’t inspected due to access restrictions.

Being aware of access limitations empowers you to:

  • Follow up with further inspections if practicable
  • Ask further questions
  • Get clear on the inspectors perspective
  • Make an informed decision before buying

Looking for an Inspector?

Book now through Aus Property Report and get connected with qualified, trusted inspectors in your area.

Find an Inspector
✓Verified Inspectors✓Australia Wide✓Instant Booking